Correcting Your PlayStation three (PS3 YLOD Maintenance)

The Playstation three (a.k.a. PS3) has become the most powerful and well known gaming consoles out available on the market suitable now. Regrettably, the fame isn’t going to occur without having a couple flaws. The PS3 was created to be slick and beautiful, nonetheless it appears to be that the same form of attention to engineering was not offered towards the Playstation 3’s cooling capabilities. Considered one of probably the most well known concerns with modern day gaming consoles including the Playstation 3 may be the lack of ability to help keep by itself neat. After overheated, the Playstation three will not transform on. Signs of the difficulty incorporate the system “beeping” three occasions in addition to a yellow flashing light close to the on button. This PS3 issue is extremely cited given that the “Yellow Gentle of Death” or YLOD. Let’s see what we could do to revive this high-priced paper weight back to lifestyle especially if your guarantee now not applies superior ball screw repair.

Fantastic information, a PS3 correct does exist! Like a matter of actuality, there may be a resolve for almost each individual trouble your Playstation may possibly experience later on. In the following paragraphs we will glimpse precisely at PS3 YLOD difficulty that seriously plagues initially by 3rd era Playstation 3s (generally known as Excess fat PS3 products).

Why Does the PS3 YLOD Take place?

A single key reason (99% on the time) why your Playstaion three would practical experience a YLOD is if it experienced overheated. Overheating a PS3 would result in solder balls beneath the methods CPU and GPU to become brittle and crack. This can be because of a layout flaw while in the Playstation three for the reason that the console is not able to get rid of the warmth that it is generating.

Do it On your own: PS3 YLOD Correct

Tools Required-
1x Playstation three with YLOD
1x 1500W industrial heatgun
1x Bottle of no-clean flux
1x Roll of masking tape
1x Tamper-proof T-screw driver
1x Phillips screwdriver
1x Warmth resistant area
1x Pack of cotton balls
1x Bottle of Acetone and Rubbing Liquor
1x Tube of thermal paste

Summary of Steps-

one) Shut down your Playstation three and make sure all ability cables are unplugged (Basic safety to start with!).

2) Remove the warranty seal located earlier mentioned the harddrive disk bay. Then make use of the tamper-proof T screwdriver clear away the screw that holds the top protect to the PS3.

3) Employing your Philips screwdriver take out every one of the screws securing the very best shell on the PS3.

4) Meticulously disassemble the detachable pieces (Ability offer, Blue-ray drive, Blue tooth board with wireless antenna, capacitance electricity swap, along with the HDD).]

5) Remove the screws securing the PS3’s motherboard. Eliminate the lover and warmth sink and warmth sink shroud hooked up towards the motherboard.

6) Utilizing the cotton balls soaked with acetone, thoroughly clean the thermal paste from CPU and warmth sink surfaces.

seven) Tape motherboard down over a warmth resistant floor to make sure that it sits flat (perform close to by using a corner of the surface area to locate a very good position for the motherboard). Taping the PS3’s motherboard down will avoid it from warping under the warmth with the heatgun.

8) Using the warmth gun’s low placing, heat up the whole motherboard (~3 minutes). Then apply the no-clean flux beneath the CPU and GPU liberally.

nine) Use the heat gun’s high environment heat the CPU and GPU up. Continue to keep the heat gun about 1-2″ far from the surface area of your PS3 motherboard, but transfer the warmth gun around the chips constantly in order to avoid burn hurt (persist for ~8-10 minutes).

ten) Make it possible for the motherboard to chill down for 20-30 minutes.

11) Reassemble the Playstation three to it really is first ailment (cautious to interchange every single screw and plug to its rightful put).

twelve) Plug the ability twine again in and switch about the PS3.

If executed properly, your Playstation 3 YLOD dilemma ought to be long gone. This PS3 fix should really choose 1 to 2 hours dependent with your ability with electronics. In the event you call for a good extra in depth, step-by-step fix walkthrough with shots and almost everything remember to glance to the underside from the write-up for the good guide that i use at the same time.

This entry was posted in Blogs. Bookmark the permalink.

Leave a Reply

Your email address will not be published. Required fields are marked *